mirror of
https://github.com/IoTManagerProject/IoTManager.git
synced 2026-03-27 14:42:18 +03:00
99 lines
3.1 KiB
C++
99 lines
3.1 KiB
C++
/*
|
|
* The MySensors Arduino library handles the wireless radio link and protocol
|
|
* between your home built sensors/actuators and HA controller of choice.
|
|
* The sensors forms a self healing radio network with optional repeaters. Each
|
|
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
|
|
* network topology allowing messages to be routed to nodes.
|
|
*
|
|
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
|
|
* Copyright (C) 2013-2019 Sensnology AB
|
|
* Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors
|
|
*
|
|
* Documentation: http://www.mysensors.org
|
|
* Support Forum: http://forum.mysensors.org
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* version 2 as published by the Free Software Foundation.
|
|
*
|
|
*******************************
|
|
*
|
|
* REVISION HISTORY
|
|
* Version 1.0 - Henrik Ekblad
|
|
*
|
|
* DESCRIPTION
|
|
* This is an example of sensors using RS485 as transport layer
|
|
*
|
|
* Motion Sensor example using HC-SR501
|
|
* http://www.mysensors.org/build/motion
|
|
*
|
|
* If your Arduino board has additional serial ports
|
|
* you can use to connect the RS485 module.
|
|
* Otherwise, the transport uses AltSoftSerial to handle two serial
|
|
* links on one Arduino. Use the following pins for RS485 link
|
|
*
|
|
* Board Transmit Receive PWM Unusable
|
|
* ----- -------- ------- ------------
|
|
* Teensy 3.0 & 3.1 21 20 22
|
|
* Teensy 2.0 9 10 (none)
|
|
* Teensy++ 2.0 25 4 26, 27
|
|
* Arduino Uno 9 8 10
|
|
* Arduino Leonardo 5 13 (none)
|
|
* Arduino Mega 46 48 44, 45
|
|
* Wiring-S 5 6 4
|
|
* Sanguino 13 14 12 *
|
|
*
|
|
*/
|
|
|
|
// Enable debug prints to serial monitor
|
|
#define MY_DEBUG
|
|
|
|
// Enable RS485 transport layer
|
|
#define MY_RS485
|
|
|
|
// Define this to enables DE-pin management on defined pin
|
|
#define MY_RS485_DE_PIN 2
|
|
|
|
// Set RS485 baud rate to use
|
|
#define MY_RS485_BAUD_RATE 9600
|
|
|
|
// Enable this if RS485 is connected to a hardware serial port
|
|
//#define MY_RS485_HWSERIAL Serial1
|
|
|
|
#include <MySensors.h>
|
|
|
|
uint32_t SLEEP_TIME = 120000; // Sleep time between reports (in milliseconds)
|
|
#define DIGITAL_INPUT_SENSOR 3 // The digital input you attached your motion sensor. (Only 2 and 3 generates interrupt!)
|
|
#define CHILD_ID 1 // Id of the sensor child
|
|
|
|
// Initialize motion message
|
|
MyMessage msg(CHILD_ID, V_TRIPPED);
|
|
|
|
void setup()
|
|
{
|
|
pinMode(DIGITAL_INPUT_SENSOR, INPUT); // sets the motion sensor digital pin as input
|
|
}
|
|
|
|
void presentation()
|
|
{
|
|
// Send the sketch version information to the gateway and Controller
|
|
sendSketchInfo("Motion Sensor", "1.0");
|
|
|
|
// Register all sensors to gw (they will be created as child devices)
|
|
present(CHILD_ID, S_MOTION);
|
|
}
|
|
|
|
void loop()
|
|
{
|
|
// Read digital motion value
|
|
bool tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH;
|
|
|
|
Serial.println(tripped);
|
|
send(msg.set(tripped?"1":"0")); // Send tripped value to gw
|
|
|
|
// Sleep until interrupt comes in on motion sensor. Send update every two minute.
|
|
sleep(digitalPinToInterrupt(DIGITAL_INPUT_SENSOR), CHANGE, SLEEP_TIME);
|
|
}
|
|
|
|
|