mirror of
https://github.com/IoTManagerProject/IoTManager.git
synced 2026-03-29 15:42:20 +03:00
131 lines
4.6 KiB
C++
131 lines
4.6 KiB
C++
/*
|
|
* The MySensors Arduino library handles the wireless radio link and protocol
|
|
* between your home built sensors/actuators and HA controller of choice.
|
|
* The sensors forms a self healing radio network with optional repeaters. Each
|
|
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
|
|
* network topology allowing messages to be routed to nodes.
|
|
*
|
|
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
|
|
* Copyright (C) 2013-2019 Sensnology AB
|
|
* Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors
|
|
*
|
|
* Documentation: http://www.mysensors.org
|
|
* Support Forum: http://forum.mysensors.org
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* version 2 as published by the Free Software Foundation.
|
|
*
|
|
*******************************
|
|
*
|
|
* REVISION HISTORY
|
|
* Version 1.0 - Henrik Ekblad
|
|
* Contribution by a-lurker and Anticimex,
|
|
* Contribution by Norbert Truchsess <norbert.truchsess@t-online.de>
|
|
* Contribution by Ivo Pullens (ESP8266 support)
|
|
*
|
|
* DESCRIPTION
|
|
* The EthernetGateway sends data received from sensors to the WiFi link.
|
|
* The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
|
|
*
|
|
* VERA CONFIGURATION:
|
|
* Enter "ip-number:port" in the ip-field of the Arduino GW device. This will temporarily override any serial configuration for the Vera plugin.
|
|
* E.g. If you want to use the default values in this sketch enter: 192.168.178.66:5003
|
|
*
|
|
* LED purposes:
|
|
* - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs in your sketch, only the LEDs that is defined is used.
|
|
* - RX (green) - blink fast on radio message received. In inclusion mode will blink fast only on presentation received
|
|
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
|
|
* - ERR (red) - fast blink on error during transmission error or receive crc error
|
|
*
|
|
* See https://www.mysensors.org/build/connect_radio for wiring instructions.
|
|
*
|
|
* If you are using a "barebone" ESP8266, see
|
|
* https://www.mysensors.org/build/esp8266_gateway#wiring-for-barebone-esp8266
|
|
*
|
|
* Inclusion mode button:
|
|
* - Connect GPIO5 (=D1) via switch to GND ('inclusion switch')
|
|
*
|
|
* Hardware SHA204 signing is currently not supported!
|
|
*
|
|
* Make sure to fill in your ssid and WiFi password below for ssid & pass.
|
|
*/
|
|
|
|
// Enable debug prints to serial monitor
|
|
#define MY_DEBUG
|
|
|
|
// Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h
|
|
#define MY_BAUD_RATE 9600
|
|
|
|
// Enables and select radio type (if attached)
|
|
#define MY_RADIO_RF24
|
|
//#define MY_RADIO_RFM69
|
|
//#define MY_RADIO_RFM95
|
|
|
|
#define MY_GATEWAY_ESP8266
|
|
|
|
#define MY_WIFI_SSID "MySSID"
|
|
#define MY_WIFI_PASSWORD "MyVerySecretPassword"
|
|
|
|
// Enable UDP communication
|
|
//#define MY_USE_UDP // If using UDP you need to set MY_CONTROLLER_IP_ADDRESS or MY_CONTROLLER_URL_ADDRESS below
|
|
|
|
// Set the hostname for the WiFi Client. This is the hostname
|
|
// it will pass to the DHCP server if not static.
|
|
#define MY_HOSTNAME "ESP8266_GW"
|
|
|
|
// Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
|
|
//#define MY_IP_ADDRESS 192,168,178,87
|
|
|
|
// If using static ip you can define Gateway and Subnet address as well
|
|
//#define MY_IP_GATEWAY_ADDRESS 192,168,178,1
|
|
//#define MY_IP_SUBNET_ADDRESS 255,255,255,0
|
|
|
|
// The port to keep open on node server mode
|
|
#define MY_PORT 5003
|
|
|
|
// How many clients should be able to connect to this gateway (default 1)
|
|
#define MY_GATEWAY_MAX_CLIENTS 2
|
|
|
|
// Controller ip address. Enables client mode (default is "server" mode).
|
|
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
|
|
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68
|
|
//#define MY_CONTROLLER_URL_ADDRESS "my.controller.org"
|
|
|
|
// Enable inclusion mode
|
|
//#define MY_INCLUSION_MODE_FEATURE
|
|
|
|
// Enable Inclusion mode button on gateway
|
|
//#define MY_INCLUSION_BUTTON_FEATURE
|
|
// Set inclusion mode duration (in seconds)
|
|
//#define MY_INCLUSION_MODE_DURATION 60
|
|
// Digital pin used for inclusion mode button
|
|
//#define MY_INCLUSION_MODE_BUTTON_PIN D1
|
|
|
|
// Set blinking period
|
|
//#define MY_DEFAULT_LED_BLINK_PERIOD 300
|
|
|
|
// Flash leds on rx/tx/err
|
|
// Led pins used if blinking feature is enabled above
|
|
//#define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin
|
|
//#define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin
|
|
//#define MY_DEFAULT_TX_LED_PIN 16 // the PCB, on board LED
|
|
|
|
#include <MySensors.h>
|
|
|
|
void setup()
|
|
{
|
|
// Setup locally attached sensors
|
|
}
|
|
|
|
void presentation()
|
|
{
|
|
// Present locally attached sensors here
|
|
}
|
|
|
|
void loop()
|
|
{
|
|
// Send locally attached sensors data here
|
|
}
|
|
|