{
    "mark": "iotm",
    "config": [
        {
            "global": 0,
            "type": "Reading",
            "subtype": "MQgas",
            "id": "MQ135",
            "widget": "anydataPpm",
            "page": "Сенсоры",
            "descr": "MQ-135",
            "Series": 135,
            "Gas": "CO2",
            "Rl on board": "10",
            "Ro in clean air": 0,
            "Rl/Ro in clean air": "0",
            "PPM in clean air": "397.13",
            "aLimit": "-0.42",
            "bLimit": "1.92",
            "Warm up time": "60",
            "Sample interval": 20,
            "Sample times": "10",
            "Calibtation intensity": 5,
            "autoCalibration": 1,
            "autoCalib.Period": 1,
            "TempHum correction": 1,
            "k1": 0.00672096284322792,
            "k2": -0.0159038179354688,
            "b1": -0.741244323718154,
            "b2": 1.77535862501753,
            "temperature": "20",
            "idTempSensor": "Tmp",
            "humidity": "50",
            "idHumSensor": "Hum",
            "Debug": 1,
            "plus": 0,
            "multiply": 1,
            "round": 1,
            "pin-Esp32": 34,
            "operating voltage": 3.3,
            "int": 15
        },
        {
            "global": 0,
            "type": "Writing",
            "subtype": "Loging",
            "id": "log",
            "widget": "chart1",
            "page": "Графики",
            "descr": "CO2",
            "int": "1",
            "logid": "MQ135",
            "points": 300
        },
        {
            "global": 0,
            "type": "Reading",
            "subtype": "VButton",
            "id": "vbtn",
            "needSave": 0,
            "widget": "toggle",
            "page": "Калибровка",
            "descr": "Быстрая Калибровка",
            "int": "0",
            "val": "0"
        },
        {
            "global": 0,
            "type": "Reading",
            "subtype": "Bme280t",
            "id": "Tmp",
            "widget": "anydataTmp",
            "page": "Сенсоры",
            "descr": "Температура",
            "int": 15,
            "addr": "0x76",
            "round": 1
        },
        {
            "global": 0,
            "type": "Reading",
            "subtype": "Bme280h",
            "id": "Hum",
            "widget": "anydataHum",
            "page": "Сенсоры",
            "descr": "Влажность",
            "int": 15,
            "addr": "0x76",
            "round": 1
        },
        {
            "global": 0,
            "type": "Writing",
            "subtype": "Timer",
            "id": "timer0",
            "widget": "nil",
            "page": "",
            "descr": "Таймер",
            "int": "1",
            "countDown": 15,
            "ticker": "0",
            "repeat": "1",
            "needSave": 0
        },
        {
            "global": 0,
            "type": "Reading",
            "subtype": "Variable",
            "id": "vout",
            "needSave": 0,
            "widget": "anydataDef",
            "page": "Калибровка",
            "descr": "Последняя калибровка",
            "int": "0",
            "val": "0.0",
            "map": "1024,1024,1,100",
            "plus": 0,
            "multiply": 1,
            "round": 0
        },
        {
            "global": 0,
            "type": "Reading",
            "subtype": "VButton",
            "id": "vbtn13",
            "needSave": 0,
            "widget": "toggle",
            "page": "Калибровка",
            "descr": "Автокалибровка выкл/вкл",
            "int": "0",
            "val": "1"
        },
        {
            "global": 0,
            "type": "Reading",
            "subtype": "VButton",
            "id": "vbtn50",
            "needSave": 0,
            "widget": "toggle",
            "page": "Калибровка",
            "descr": "Накопительная Калибровка",
            "int": "0",
            "val": "0"
        }
    ]
}

scenario=>#запускаем разово калибровку без параметрова или с ними
if vbtn then {
MQ135.calibrate();
#MQ135.calibrateR0(42);
#MQ135.calibrateRlRo(0.60);
#MQ135.calibratePPM(400);
#MQ135.TempHumCorrection(20,55);
#MQ135.TempHumCorrection(Tmp,Hum);
 vbtn = 0;}

#обновляем время последней калибровки
if MQ135 then {
vout = MQ135.lastCalibration();
}


#влючаем/выключаем автокалибровку
if vbtn13 == 1 then  MQ135.setAutoCalibration(1)
if vbtn13 == 0 then  MQ135.setAutoCalibration(0)


#принудительно запускаем автокалибровку
if vbtn50 then {
MQ135.runAutoCalibration();
vbtn50 = 0;
}

#можно по таймеру передавать температуру и влажность в модуль. Но проще сразу вписать id этих элементов в настройки MQ 
#if timer0 == 0 then MQ135.TempHumCorrection(Tmp,Hum);