gatewayTransportSend

lib/MySensors/examples/VibrationSensor/VibrationSensor.ino

@@ -0,0 +1,101 @@
+/*
+ * The MySensors Arduino library handles the wireless radio link and protocol
+ * between your home built sensors/actuators and HA controller of choice.
+ * The sensors forms a self healing radio network with optional repeaters. Each
+ * repeater and gateway builds a routing tables in EEPROM which keeps track of the
+ * network topology allowing messages to be routed to nodes.
+ *
+ * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
+ * Copyright (C) 2013-2019 Sensnology AB
+ * Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors
+ *
+ * Documentation: http://www.mysensors.org
+ * Support Forum: http://forum.mysensors.org
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ *******************************
+ *
+ * DESCRIPTION
+ *
+ * Vibration Sensor
+ *
+ * connect the sensor as follows :
+ *
+ * VCC       >>> 5V
+ * S         >>> D3
+ * GND       >>> GND
+ *
+ * Based on: http://www.dfrobot.com/wiki/index.php/DFRobot_Digital_Vibration_Sensor_V2_SKU:DFR0027
+ * Contributor: epierre
+ */
+
+// Enable debug prints to serial monitor
+#define MY_DEBUG
+
+// Enable and select radio type attached
+#define MY_RADIO_RF24
+//#define MY_RADIO_NRF5_ESB
+//#define MY_RADIO_RFM69
+//#define MY_RADIO_RFM95
+
+#include <MySensors.h>
+#include <Wire.h>
+
+#define CHILD_ID_VIBRATION 0
+#define VIBRATION_SENSOR_DIGITAL_PIN 3
+#define SensorLED     13
+
+uint32_t SLEEP_TIME = 10*1000; // Sleep time between reads (in seconds)
+
+//VARIABLES
+int val = 0;           // variable to store the value coming from the sensor
+float valVIBRATION =0.0;
+float lastVIBRATION =0.0;
+unsigned char state = 0;
+
+MyMessage vibrationMsg(CHILD_ID_VIBRATION, V_LEVEL);
+
+void setup()
+{
+	pinMode(VIBRATION_SENSOR_DIGITAL_PIN, INPUT);
+	attachInterrupt(digitalPinToInterrupt(VIBRATION_SENSOR_DIGITAL_PIN), blink,
+	                FALLING); // Trigger the blink function when the falling edge is detected
+	pinMode(SensorLED, OUTPUT);
+}
+
+void presentation()
+{
+	// Send the sketch version information to the gateway and Controller
+	sendSketchInfo("VIBRATION Sensor", "1.0");
+
+	// Register all sensors to gateway (they will be created as child devices)
+	present(CHILD_ID_VIBRATION, S_VIBRATION);
+}
+
+void loop()
+{
+
+	if(state>=40) { // basically below 40 so ignire basic level
+		send(vibrationMsg.set(int16_t(state)));
+		state = 0;
+		digitalWrite(SensorLED,HIGH);
+	}    else {
+		state = 0;
+		digitalWrite(SensorLED,LOW);
+	}
+
+
+	// Power down the radio.  Note that the radio will get powered back up
+	// on the next write() call.
+	delay(1000); //delay to allow serial to fully print before sleep
+
+	sleep(SLEEP_TIME); //sleep for: sleepTime
+}
+
+void blink()//Interrupts function
+{
+	state++;
+}