gatewayTransportSend

lib/MySensors/examples/GatewayW5100/GatewayW5100.ino

@@ -0,0 +1,142 @@
+/*
+ * The MySensors Arduino library handles the wireless radio link and protocol
+ * between your home built sensors/actuators and HA controller of choice.
+ * The sensors forms a self healing radio network with optional repeaters. Each
+ * repeater and gateway builds a routing tables in EEPROM which keeps track of the
+ * network topology allowing messages to be routed to nodes.
+ *
+ * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
+ * Copyright (C) 2013-2019 Sensnology AB
+ * Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors
+ *
+ * Documentation: http://www.mysensors.org
+ * Support Forum: http://forum.mysensors.org
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ *******************************
+ *
+ * REVISION HISTORY
+ * Version 1.0 - Henrik Ekblad
+ * Contribution by a-lurker and Anticimex
+ * Contribution by Norbert Truchsess <norbert.truchsess@t-online.de>
+ * Contribution by Tomas Hozza <thozza@gmail.com>
+ *
+ *
+ * DESCRIPTION
+ * The EthernetGateway sends data received from sensors to the ethernet link.
+ * The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
+ *
+ * The GW code is designed for Arduino 328p / 16MHz.  ATmega168 does not have enough memory to run this program.
+ *
+ * LED purposes:
+ * - To use the feature, uncomment MY_DEFAULT_xxx_LED_PIN in the sketch below
+ * - RX (green) - blink fast on radio message received. In inclusion mode will blink fast only on presentation received
+ * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
+ * - ERR (red) - fast blink on error during transmission error or receive crc error
+ *
+ * See http://www.mysensors.org/build/ethernet_gateway for wiring instructions.
+ *
+ */
+
+// Enable debug prints to serial monitor
+#define MY_DEBUG
+
+// Enable and select radio type attached
+#define MY_RADIO_RF24
+//#define MY_RADIO_NRF5_ESB
+//#define MY_RADIO_RFM69
+//#define MY_RADIO_RFM95
+
+// Enable gateway ethernet module type
+#define MY_GATEWAY_W5100
+
+// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
+//#define MY_W5100_SPI_EN 4
+
+// Enable Soft SPI for NRF radio (note different radio wiring is required)
+// The W5100 ethernet module seems to have a hard time co-operate with
+// radio on the same spi bus.
+#if !defined(MY_W5100_SPI_EN) && !defined(ARDUINO_ARCH_SAMD)
+#define MY_SOFTSPI
+#define MY_SOFT_SPI_SCK_PIN 14
+#define MY_SOFT_SPI_MISO_PIN 16
+#define MY_SOFT_SPI_MOSI_PIN 15
+#endif
+
+// When W5100 is connected we have to move CE/CSN pins for NRF radio
+#ifndef MY_RF24_CE_PIN
+#define MY_RF24_CE_PIN 5
+#endif
+#ifndef MY_RF24_CS_PIN
+#define MY_RF24_CS_PIN 6
+#endif
+
+// Enable UDP communication
+//#define MY_USE_UDP  // If using UDP you need to set MY_CONTROLLER_IP_ADDRESS or MY_CONTROLLER_URL_ADDRESS below
+
+// Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
+#define MY_IP_ADDRESS 192,168,178,66
+
+// If using static ip you can define Gateway and Subnet address as well
+//#define MY_IP_GATEWAY_ADDRESS 192,168,178,1
+//#define MY_IP_SUBNET_ADDRESS 255,255,255,0
+
+// Renewal period if using DHCP
+//#define MY_IP_RENEWAL_INTERVAL 60000
+
+// The port to keep open on node server mode / or port to contact in client mode
+#define MY_PORT 5003
+
+// Controller ip address. Enables client mode (default is "server" mode).
+// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
+//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254
+//#define MY_CONTROLLER_URL_ADDRESS "my.controller.org"
+
+// The MAC address can be anything you want but should be unique on your network.
+// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
+// Note that most of the Arduino examples use  "DEAD BEEF FEED" for the MAC address.
+#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
+
+
+// Enable inclusion mode
+#define MY_INCLUSION_MODE_FEATURE
+// Enable Inclusion mode button on gateway
+//#define MY_INCLUSION_BUTTON_FEATURE
+// Set inclusion mode duration (in seconds)
+#define MY_INCLUSION_MODE_DURATION 60
+// Digital pin used for inclusion mode button
+//#define MY_INCLUSION_MODE_BUTTON_PIN  3
+
+// Set blinking period
+#define MY_DEFAULT_LED_BLINK_PERIOD 300
+
+// Flash leds on rx/tx/err
+// Uncomment to override default HW configurations
+//#define MY_DEFAULT_ERR_LED_PIN 7  // Error led pin
+//#define MY_DEFAULT_RX_LED_PIN  8  // Receive led pin
+//#define MY_DEFAULT_TX_LED_PIN  9  // Transmit led pin
+
+#if defined(MY_USE_UDP)
+#include <EthernetUdp.h>
+#endif
+#include <Ethernet.h>
+#include <MySensors.h>
+
+void setup()
+{
+	// Setup locally attached sensors
+}
+
+void presentation()
+{
+	// Present locally attached sensors here
+}
+
+void loop()
+{
+	// Send locally attached sensors data here
+}
+