добавление mysensors в процессе не рабочая версия

lib/MySensors/examples/GatewayW5100MQTTClient/GatewayW5100MQTTClient.ino

@@ -0,0 +1,154 @@
+/*
+ * The MySensors Arduino library handles the wireless radio link and protocol
+ * between your home built sensors/actuators and HA controller of choice.
+ * The sensors forms a self healing radio network with optional repeaters. Each
+ * repeater and gateway builds a routing tables in EEPROM which keeps track of the
+ * network topology allowing messages to be routed to nodes.
+ *
+ * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
+ * Copyright (C) 2013-2019 Sensnology AB
+ * Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors
+ *
+ * Documentation: http://www.mysensors.org
+ * Support Forum: http://forum.mysensors.org
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ *******************************
+ *
+ * REVISION HISTORY
+ * Version 1.0 - Henrik Ekblad
+ *
+ * DESCRIPTION
+ * The W5100 MQTT gateway sends radio network (or locally attached sensors) data to your MQTT broker.
+ * The node also listens to MY_MQTT_TOPIC_PREFIX and sends out those messages to the radio network
+ *
+ * LED purposes:
+ * - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h
+ * - RX (green) - blink fast on radio message received. In inclusion mode will blink fast only on presentation received
+ * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
+ * - ERR (red) - fast blink on error during transmission error or receive crc error
+ *
+ * See http://www.mysensors.org/build/esp8266_gateway for wiring instructions.
+ * nRF24L01+  ESP8266
+ * VCC        VCC
+ * CE         GPIO4
+ * CSN/CS     GPIO15
+ * SCK        GPIO14
+ * MISO       GPIO12
+ * MOSI       GPIO13
+ *
+ * Not all ESP8266 modules have all pins available on their external interface.
+ * This code has been tested on an ESP-12 module.
+ * The ESP8266 requires a certain pin configuration to download code, and another one to run code:
+ * - Connect REST (reset) via 10K pullup resistor to VCC, and via switch to GND ('reset switch')
+ * - Connect GPIO15 via 10K pulldown resistor to GND
+ * - Connect CH_PD via 10K resistor to VCC
+ * - Connect GPIO2 via 10K resistor to VCC
+ * - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch')
+ *
+  * Inclusion mode button:
+ * - Connect GPIO5 via switch to GND ('inclusion switch')
+ *
+ * Hardware SHA204 signing is currently not supported!
+ *
+ * Make sure to fill in your ssid and WiFi password below for ssid & pass.
+ */
+
+
+// Enable debug prints to serial monitor
+#define MY_DEBUG
+
+// Enables and select radio type (if attached)
+#define MY_RADIO_RF24
+//#define MY_RADIO_RFM69
+//#define MY_RADIO_RFM95
+
+#define MY_GATEWAY_MQTT_CLIENT
+
+// Set this node's subscribe and publish topic prefix
+#define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway1-out"
+#define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway1-in"
+
+// Set MQTT client id
+#define MY_MQTT_CLIENT_ID "mysensors-1"
+
+// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
+//#define MY_W5100_SPI_EN 4
+
+// Enable Soft SPI for NRF radio (note different radio wiring is required)
+// The W5100 ethernet module seems to have a hard time co-operate with
+// radio on the same spi bus.
+#if !defined(MY_W5100_SPI_EN) && !defined(ARDUINO_ARCH_SAMD)
+#define MY_SOFTSPI
+#define MY_SOFT_SPI_SCK_PIN 14
+#define MY_SOFT_SPI_MISO_PIN 16
+#define MY_SOFT_SPI_MOSI_PIN 15
+#endif
+
+// When W5100 is connected we have to move CE/CSN pins for NRF radio
+#ifndef MY_RF24_CE_PIN
+#define MY_RF24_CE_PIN 5
+#endif
+#ifndef MY_RF24_CS_PIN
+#define MY_RF24_CS_PIN 6
+#endif
+
+// Enable these if your MQTT broker requires username/password
+//#define MY_MQTT_USER "username"
+//#define MY_MQTT_PASSWORD "password"
+
+// Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
+#define MY_IP_ADDRESS 192,168,178,87
+
+// If using static ip you can define Gateway and Subnet address as well
+//#define MY_IP_GATEWAY_ADDRESS 192,168,178,1
+//#define MY_IP_SUBNET_ADDRESS 255,255,255,0
+
+// MQTT broker ip address or url. Define one or the other.
+//#define MY_CONTROLLER_URL_ADDRESS "m20.cloudmqtt.com"
+#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68
+
+// The MQTT broker port to to open
+#define MY_PORT 1883
+
+/*
+// Enable inclusion mode
+#define MY_INCLUSION_MODE_FEATURE
+// Enable Inclusion mode button on gateway
+//#define MY_INCLUSION_BUTTON_FEATURE
+// Set inclusion mode duration (in seconds)
+#define MY_INCLUSION_MODE_DURATION 60
+// Digital pin used for inclusion mode button
+//#define MY_INCLUSION_MODE_BUTTON_PIN  3
+
+// Set blinking period
+#define MY_DEFAULT_LED_BLINK_PERIOD 300
+
+// Flash leds on rx/tx/err
+// Uncomment to override default HW configurations
+//#define MY_DEFAULT_ERR_LED_PIN 16  // Error led pin
+//#define MY_DEFAULT_RX_LED_PIN  16  // Receive led pin
+//#define MY_DEFAULT_TX_LED_PIN  16  // the PCB, on board LED
+*/
+
+#include <Ethernet.h>
+#include <MySensors.h>
+
+void setup()
+{
+	// Setup locally attached sensors
+}
+
+void presentation()
+{
+	// Present locally attached sensors here
+}
+
+void loop()
+{
+	// Send locally attached sensors data here
+}
+